ASTM E1300 09A PDF

The values stated in SI units astmm to be regarded as the standard. New Products — more. Referenced Documents purchase separately The documents listed below are referenced within the subject standard but are not provided as part of the standard. ASTM-E, — For conversion of quantities in various systems of measurements to SI units, refer to SI This practice applies only to monolithic, laminated, or insulating glass constructions of rectangular shape with continuous lateral support along one, two, three, or four edges. Appendix X3 presents a procedure to compute approximate probability of breakage for annealed AN monolithic glass lites simply supported on four sides.

Author:Morr Migore
Country:Zambia
Language:English (Spanish)
Genre:Technology
Published (Last):3 June 2014
Pages:292
PDF File Size:3.77 Mb
ePub File Size:4.73 Mb
ISBN:960-5-70033-824-7
Downloads:86393
Price:Free* [*Free Regsitration Required]
Uploader:Dourg



Shakazshura ASTM-E, — Referenced Documents purchase separately The documents listed below are referenced within the subject standard but are not provided as part of the standard. Search book title Enter keywords for book title search. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

For conversion of quantities in various systems of measurements to SI units, refer to SI This practice applies to vertical and sloped glazing in buildings for which the specified design loads consist of wind load, snow load and self-weight with a total combined magnitude less than or equal to 10 kPa psf.

D Practice for Plastics: The final thickness and type of glass selected also depends upon a variety of other factors see 5. The values given in parentheses are for information only. Determination and Report of Procedures. Land Use and Development. Charts in this practice provide a means to determine approximate maximum lateral glass deflection.

Please login to your authorized staff account to use this feature. E Standard Guide for Thermocouple Verification. Appendix X3 presents a procedure to compute approximate probability of breakage for annealed AN monolithic glass lites simply supported on four sides. There were no books found for the e search filters. Link to Active This link will always route to the current Active version of the standard.

Click here to download full list of books. HUNTER PDF This practice assumes that 1 the supported glass edges for two, three, and four-sided support conditions are simply supported and free to slip in plane; 2 glass supported on two sides acts as a simply supported beam; and 3 glass supported on one side acts as a cantilever.

Enter your personal account email address to request a password reset: The values stated in SI units are to be regarded as astn standard. Print 1 2 3 4 5 page sstarting from page current page. E Terminology of Building Constructions. Referenced Documents purchase separately The documents listed below are referenced within the subject standard but are not provided as part of the standard.

This practice shall not apply to other applications including, but not limited to, balustrades, glass floor panels, aquariums, structural glass members, and glass shelves. No items in cart. E 32 — latest. This practice assumes that 1 the supported glass edges for two, three, and four-sided support conditions are simply supported and free to slip in plane; 2 glass supported on two sides acts as a simply supported beam; and 3 glass supported on one side acts as a cantilever.

Nails, Spikes, and Staples. For conversion of quantities in various systems of d to SI units, refer to SI Today, some 12, ASTM standards are used around the world to improve product quality, enhance safety, facilitate market access and trade, and build consumer confidence. Work Item s — proposed revisions of this standard. Appendix X1 and Appendix X2 provide additional procedures to determine maximum lateral deflection for glass simply supported on four sides.

This s assumes that 1 the supported glass edges for astk, three, and four-sided support conditions are simply supported and free atsm slip in plane; 2 glass supported on two sides acts as a simply supported beam; and 3 glass supported on one side acts as a cantilever. The values given 09x parentheses are for information only. Your cart is empty. D Practice for Plastics: Determination and Report of Procedures E Terminology of Building Constructions Keywords annealed glass; deflection; flat glass; fully tempered glass; glass; heat-strengthened glass; insulating glass; laminated glass; load resistance; monolithic glass; probability of breakage; snow load; soda lime silicate; strength; wind load; ICS Code ICS Number Code This practice shall not apply to other applications including, but not limited to, balustrades, glass floor asgm, aquariums, structural glass members, and glass shelves.

The final thickness and type of glass selected also depends upon a variety of other factors see 5. Appendix X4 lists the key variables used in calculating the mandatory type factors in Tables and comments on their conservative values.

Powered by Standards Documents. Register for a trial account. Related Posts

M83536 DATASHEET PDF

ASTM E1300-09A PDF

Zololmaran The final thickness and type of glass selected also depends upon a variety of other factors see 5. Sign In or Register. Enter your personal account email address to request a password reset: Determination and Report of Procedures. Determination and Report of Procedures.

RABINDRA SANGEET NOTATION PDF

ASTM-E-1300 (R09A)

No further reproductions authorized. E — 09a equal or different thicknesses and types including the layered NOTE 1—This practice does not address aesthetic issues caused by glass behavior of LG under long duration loads , in a sealed IG unit. These factors include but are not limited the IG unit, based on the resistance to breakage of one specific to: thermal stresses, spontaneous breakage of tempered glass, lite only. In addition, considerations set forth in lites or plies that would break at the first occurrence of a building codes along with criteria presented in safety glazing specified load and duration, typically expressed in lites per standards and site specific concerns may control the ultimate Procedure having jurisdiction and considering appropriate site specific 6. Annex A1 the upper charts of Figs A1. Summary of Practice 6.

CHARLES LARMORE POLITICAL LIBERALISM PDF

ASTM E1300 09A PDF

ASTM E 1. Scope 1. This practice shall not apply to other applications including, but not limited to, balustrades, glass floor panels, aquariums, structural glass members, and glass shelves. This practice assumes that 1 the supported glass edges for two, three, and four-sided support conditions are simply supported and free to slip in plane; 2 glass supported on two sides acts as a simply supported beam; and 3 glass supported on one side acts as a cantilever. The final thickness and type of glass selected also depends upon a variety of other factors see 5.

ADC0809 DATASHEET PDF

ASTM E1300:09a

Shakazshura ASTM-E, — Referenced Documents purchase separately The documents listed below are referenced within the subject standard but are not provided as part of the standard. Search book title Enter keywords for book title search. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. For conversion of quantities in various systems of measurements to SI units, refer to SI This practice applies to vertical and sloped glazing in buildings for which the specified design loads consist of wind load, snow load and self-weight with a total combined magnitude less than or equal to 10 kPa psf. D Practice for Plastics: The final thickness and type of glass selected also depends upon a variety of other factors see 5.

Related Articles